Call Us (480) 795-7199

TI Automotive brushless fuel pump and controller x2 (1500HP kit)

Sale!

Original price was: $1,598.00.Current price is: $1,529.00.

From TI Automotive:

TI Automotive’s new in-tank brushless fuel pump utilizes advanced technology for maximum reliability and efficiency. The result is a next-generation pump for any type of engine offering precise control of fuel pressure, lower current draw, reduced heat and less noise.
Supporting up to 1000+ HP, the BKS1000 provides more power, more torque and more speed. Matched controller with simple power and ground operations for easy maintainability. The controller features sealed electronics for weather resistance.

Fuel: GAS or FLEX
Horsepower: 1000
Flow Rate (lph): 550
Pressure (psi): 40

 

Complete your kit

Radium Engineering Brushless Fuel Pump Hanger for R35 Nissan GTR

Directly From Radium:

The Radium Engineering fuel hanger completely replaces the factory in-tank fuel pump unit in the R35 GT-R and permits up to three 39mm diameter aftermarket pumps (brushed or brushless) to supply fuel to the engine. No permanent vehicle modifications are required for installation. The pumps are housed in an aluminum collector box that is kept full during operation. This ensures that fuel starvation does not occur, even during aggressive driving. The fuel pump outlet port is -10AN ORB female threaded and includes a 6AN male adapter, while the return port is -8AN ORB female threaded and includes a 6AN male adapter. The system is compatible with alternative fuels such as methanol, ethanol, E85, etc. Radium Engineering recommends reviewing the installation instructions (link above) before purchasing.

 

From ATR Performance:

ATR is located in the Phoenix area, and as such - We experience very warm temperatures (Often in excess of 110 degrees F).  We've run every different variety of fuel pump and hanger setups and found flaws in most.  The R35 fuel tank is located above the transmission and exhaust, and fuel is known to get quite warm in the summer months.  In addition to this, many brushed pumps such as the Walbro 450 and 525 heat the fuel even more.  In fact, ethanol can get hot enough to boil inside the R35 fuel tank.  This results in fuel cavitation, engine cutting out, and eventual fuel pump failure.  When we installed this Radium hanger with two Walbro branded BRUSHLESS fuel pumps and controllers, we were able to cut the fuel temps by a minimum of 15 degrees F and have never experienced a fuel pump failure in over 3 years of use with this setup.

Fitted with two Walbro BKS1001 brushless fuel pumps, this Radium hanger will support 1500HP while running on E85 ethanol.  Please NOTE that this hanger does NOT come with fuel pumps or fuel pump wiring - We sell these items separately.

Radium engineering fuel pump relay and wiring kit

Description

From TI Automotive:

TI Automotive’s new in-tank brushless fuel pump utilizes advanced technology for maximum reliability and efficiency. The result is a next-generation pump for any type of engine offering precise control of fuel pressure, lower current draw, reduced heat and less noise.
Supporting up to 1000+ HP, the BKS1000 provides more power, more torque and more speed. Matched controller with simple power and ground operations for easy maintainability. The controller features sealed electronics for weather resistance.

Fuel: GAS or FLEX
Horsepower: 1000
Flow Rate (lph): 550
Pressure (psi): 40

 

From ATR Performance:

ATR is located in the Phoenix area, and as such – We experience very warm temperatures (Often in excess of 110 degrees F).  We’ve run every different variety of fuel pump and hanger setups and found flaws in most.  The R35 fuel tank is located above the transmission and exhaust, and fuel is known to get quite warm in the summer months.  In addition to this, many brushed pumps such as the Walbro 450 and 525 heat the fuel even more.  In fact, ethanol can get hot enough to boil inside the R35 fuel tank.  This results in fuel cavitation, engine cutting out, and eventual fuel pump failure.  When we installed two TI Automotive BRUSHLESS fuel pumps and controllers, using a Radium Engineering hanger (sold separately) – We were able to cut the fuel temps by a minimum of 15 degrees F and have never experienced a fuel pump failure in over 3 years of use with this setup.

Two TI Automotive brushless pumps fitted on a Radium hanger will support 1500HP while running on E85 ethanol.  You will also need to purchase two Radium fuel pump hardwire/Relay kits to complete installation.  We mount the brushless controllers behind the passenger side B pillar trim – right next to the fuel tank opening.  Please contact us for detailed installation instructions.  These controllers are FAR MORE reliable than the small RC car controllers sold by other companies.  Purchase with confidence

 

TWO BRUSHLESS KITS, RADIUM HANGER, AND TWO RADIUM RELAY KITS ARE REQUIRED TO COMPLETE THIS INSTALL

Additional information

Weight 10 lbs
Dimensions 12 × 12 × 12 in

Reviews

There are no reviews yet.

Be the first to review “TI Automotive brushless fuel pump and controller x2 (1500HP kit)”

Your email address will not be published. Required fields are marked *